• bbb

Top Suppliers film capacitor in parallel connection - New developed Hybrid Supercapacitor Battery – CRE

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

Our company since its inception, always regards product quality as enterprise life, continuously improve production technology, improve product quality and continuously strengthen enterprise total quality management, in strict accordance with the national standard ISO 9001:2000 for Dc-Link Capacitor For Industrial Converters , Dc-Link Capacitors For Dc Voltage Intermediate Circuit Of Wind Power Units , Electronic Film Capacitor , We promise to try our greatest to deliver you with high quality and economical products and services.
Top Suppliers film capacitor in parallel connection - New developed Hybrid Supercapacitor Battery – CRE Detail:

Application

1. Memory backup

2. Energy storage, mainly used for driving motors require a short time operation,

3. Power, higher power demand for a long time operation,

4. Instantaneous power, for applications that requires relatively high current units or peak currents ranging up to several hundreds of amperes even with a short operating time

Electrical performance and safety performance

No

Item

Test method

Test requirement

Remark

1

Standard charging mode At room temperature, the product is charged at a constant current of 1C. When the product voltage reaches the charging limit voltage of 16V, the product is charged at constant voltage until the charging current is less than 250mA.

/

 /

2

Standard discharge mode At room temperature, the discharge will be stopped when the product voltage reaches the discharge limit voltage of 9V.

/

 /

3

Rated capacitance

1. The product is charged according to the standard charging method.

The product capacity shall be no less than 60000F

 /
2. Stay 10min
3. The product discharges according to the standard discharge mode.

4

Internal resistance

Ac internal resistance tester tests, precision: 0.01 m Ω

≦5mΩ

 /

5

Discharge of high temperature

1. The product is charged according to the standard charging method.

Discharge capacity should ≥ 95% rated capacity, product appearance without deformation, no burst.

 /
2. Put the product into the incubator of 60±2℃ for 2H.
3. Discharge the product according to the standard discharge mode, recording discharge capacity.
4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

6

Low-temperature discharge

1. The product is charged according to the standard charging method.

discharge capacity≧70% no change on rated capacity, cap appearance, no burst

 /
2. Put the product into the incubator of -30±2℃ for 2H.
3. Discharge the product according to the standard discharge, recording discharge capacity.
4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

7

Cycle life

1. The product is charged according to the standard charging method.

No less than 20,000 cycles

 /
2. Stay 10min.
3. The product discharges according to the standard discharge mode.
4. Charge and discharge according to the above charging and discharging method for 20,000 cycles, until the discharge capacity is less than 80% of the initial capacity, the cycle is stopped.

Outline drawing

 

sp1

Circuit schematic diagram

sp3

Attention

1. The charging current shall not exceed the maximum charging current of this specification. Charging with a current value higher than the recommended value may cause problems in charging and discharging performance, mechanical performance, safety performance, etc. of the capacitor, resulting in heating or leakage.
2. The charging voltage shall not be higher than the rated voltage of 16V specified in this specification.
The charging voltage is higher than the rated voltage value, which may cause problems in the charging and discharging performance, mechanical performance and safety performance of the capacitor, resulting in heat or leakage.
3. The product must be charged at -30~60℃.
4. If the positive and negative poles of the module are connected correctly, reverse charging is strictly prohibited.
5. The discharge current shall not exceed the maximum discharge current specified in the specification.
6. The product must be discharged at -30~60℃.
7. Product voltage is lower than 9V, please do not force discharge;Full charge before use.


Product detail pictures:

Top Suppliers film capacitor in parallel connection - New developed Hybrid Supercapacitor Battery – CRE detail pictures

Top Suppliers film capacitor in parallel connection - New developed Hybrid Supercapacitor Battery – CRE detail pictures


Related Product Guide:

Dedicated to strict quality management and thoughtful client services, our experienced staff customers are generally available to discuss your demands and guarantee full client pleasure for Top Suppliers film capacitor in parallel connection - New developed Hybrid Supercapacitor Battery – CRE , The product will supply to all over the world, such as: Malaysia, Mongolia, Czech republic, We expect to deliver merchandise and services to more users in global aftermarket markets; we launched our global branding strategy by providing our excellent products and solutions all over the world by virtue of our well reputed partners letting global users keep pace with technology innovation and achievements with us.
  • After the signing of the contract, we received satisfactory goods in a short term, this is a commendable manufacturer.
    5 Stars By Rose from Amman - 2017.10.27 12:12
    In our cooperated wholesalers, this company has the best quality and reasonable price, they are our first choice.
    5 Stars By Lindsay from Bangalore - 2018.12.22 12:52

    Send your message to us:

    Write your message here and send it to us

    Send your message to us: