Manufacturing Companies for Ac Filter Capacitor - Battery-ultracapacitor hybrid energy storage unit – CRE

Short Description:

Product Detail

Product Tags

Feedback (2)

With our outstanding administration, powerful technical capability and strict top quality handle procedure, we go on to provide our purchasers with reliable good quality, reasonable selling prices and excellent services. We goal at becoming certainly one of your most responsible partners and earning your gratification for Film Capacitor Used For Medical Imaging , Induction Capacitor , Metalized Self-Healing Film Capacitor , We welcome new and previous buyers from all walks of life to make contact with us for upcoming organization associations and mutual good results!

Manufacturing Companies for Ac Filter Capacitor - Battery-ultracapacitor hybrid energy storage unit – CRE Detail:

Application

1. Memory backup

2. Energy storage, mainly used for driving motors require a short time operation,

3. Power, higher power demand for a long time operation,

4. Instantaneous power, for applications that requires relatively high current units or peak currents ranging up to several hundreds of amperes even with a short operating time

Electrical performance and safety performance

No	Item	Test method	Test requirement	Remark
1	Standard charging mode	At room temperature, the product is charged at a constant current of 1C. When the product voltage reaches the charging limit voltage of 16V, the product is charged at constant voltage until the charging current is less than 250mA.	/	/
2	Standard discharge mode	At room temperature, the discharge will be stopped when the product voltage reaches the discharge limit voltage of 9V.	/	/
3	Rated capacitance	1. The product is charged according to the standard charging method.	The product capacity shall be no less than 60000F	/
		2. Stay 10min
		3. The product discharges according to the standard discharge mode.
4	Internal resistance	Ac internal resistance tester tests, precision: 0.01 m Ω	≦5mΩ	/
5	Discharge of high temperature	1. The product is charged according to the standard charging method.	Discharge capacity should ≥ 95% rated capacity, product appearance without deformation, no burst.	/
		2. Put the product into the incubator of 60±2℃ for 2H.
		3. Discharge the product according to the standard discharge mode, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

6	Low-temperature discharge	1. The product is charged according to the standard charging method.	discharge capacity≧70% no change on rated capacity, cap appearance, no burst	/
		2. Put the product into the incubator of -30±2℃ for 2H.
		3. Discharge the product according to the standard discharge, recording discharge capacity.
		4. After the discharge, the product will be taken out under normal temperature for 2 hours, and then visual appearance.

7	Cycle life	1. The product is charged according to the standard charging method.	No less than 20,000 cycles	/
		2. Stay 10min.
		3. The product discharges according to the standard discharge mode.
		4. Charge and discharge according to the above charging and discharging method for 20,000 cycles, until the discharge capacity is less than 80% of the initial capacity, the cycle is stopped.

Outline drawing

Circuit schematic diagram

sp3

Attention

1. The charging current shall not exceed the maximum charging current of this specification. Charging with a current value higher than the recommended value may cause problems in charging and discharging performance, mechanical performance, safety performance, etc. of the capacitor, resulting in heating or leakage.
2. The charging voltage shall not be higher than the rated voltage of 16V specified in this specification.
The charging voltage is higher than the rated voltage value, which may cause problems in the charging and discharging performance, mechanical performance and safety performance of the capacitor, resulting in heat or leakage.
3. The product must be charged at -30~60℃.
4. If the positive and negative poles of the module are connected correctly, reverse charging is strictly prohibited.
5. The discharge current shall not exceed the maximum discharge current specified in the specification.
6. The product must be discharged at -30~60℃.
7. Product voltage is lower than 9V, please do not force discharge;Full charge before use.

Product detail pictures:

Related Product Guide:

We have now our possess revenue group, design staff, technical crew, QC team and package group. We now have strict excellent regulate procedures for each process. Also, all of our workers are experienced in printing subject for Manufacturing Companies for Ac Filter Capacitor - Battery-ultracapacitor hybrid energy storage unit – CRE , The product will supply to all over the world, such as: Qatar, Luxemburg, venezuela, We'd like to invite customers from abroad to discuss business with us. We can present our clients with high quality products and excellent service. We're sure that we'll have good cooperative relationships and make a brilliant future for both parties.

automotive capacitor

High Current Capacitor

High Voltage Capacitor Manufacturer

Hydrogen power capacitor

Induction Heating For Wind Energy

Low Esl Capacitor

metallized film capacitor

Metallized Polypropylene Capacitors Manufacturers

Power Capacitor Manufacturer

Power Factor Correction Capacitor Manufacturers

We always believe that the details decides the company's product quality, in this respect, the company conform our requirements and the goods are meet our expectations.